VintageKustom.com: Comment Board » Lead III/IV Speakers

Home » VintageKustom.com » Comment Board » Lead III/IV Speakers (Help identifying unlabeled speakers)

Show: Today's Messages :: Polls :: Message Navigator

Lead III/IV Speakers [message #18129]

Sun, 03 February 2013 14:07

benn
Messages: 11
Registered: February 2013

Junior Member

I have an old Kustom 4x12. It's ported, made of MDF (?), and devoid of any helpful markings to tell me what model it is. From what I've gathered it's from the mid-70s. and is either a Lead III or Lead IV. It looks like this:

http://img.photobucket.com/albums/v401/vivalaben1/kuskat040.jpg

The speakers in it are unlabeled. I've read that these cabs came from the factory with either Eminence or SRO speakers, but its such an old cab that they could very well have been swapped at some point. The magnets of the speakers (which are round, not square) in my cab are stamped:

513-105782
8-16 ohms
29563
8858014

Do any of those numbers mean anything to you folks? I'd love some more info on what these mystery speakers are if anybody can help! Also, if anybody has any idea what model in particular this cab is, or how to tell the difference between a Lead III and IV I'd appreciate it. Thanks!

Report message to a moderator

Re: Lead III/IV Speakers [message #18131 is a reply to message #18129]

Sun, 03 February 2013 14:49

pleat
Messages: 1454
Registered: June 2004
Location: Belding, Mi

Senior Member

The number on the speakers don't match anything I have on file. The Lead lll cab is 28"x28"x15 1/2" deep. will have one speaker jack. Original weight is 108lbs. Should have 4 or 6 oval vent holes in the back of the cab.
The Lead lV cab is 34" tall x 31" wide, and 15 1/2" deep. Weight is 112lbs. The cab should have two speaker output jacks with each pair of speakers connecting to the two amps inside the Lead lV head.
After 30+ years, it's hard to say what the speakers are or how the cabinet is wired. Photos of the actual cab front back and inside will shed more light on what you have.
pleat

Report message to a moderator

Re: Lead III/IV Speakers [message #18132 is a reply to message #18129]

Sun, 03 February 2013 14:58

benn
Messages: 11
Registered: February 2013

Junior Member

Thanks for the quick reply! The measurements, single jack, and 6 ports all seem to match your description of the Lead III so thanks for that clarification! I'll snap some photos of the inside of the cab ASAP, but from being inside it I know that the speakers measure 16 ohms and are wired in parallel. Also, its visible from the front of the cab that they have the vented voice coil dust caps like the original speakers pictured in the photo I posted.

Report message to a moderator

Re: Lead III/IV Speakers [message #18134 is a reply to message #18129]

Mon, 04 February 2013 09:44

stevem
Messages: 4775
Registered: June 2004
Location: NY

Senior Member

When viewing your cabinet from the front as in the photo you posted, do the speakers each that aluminum center voice coil cover with the black hole in the center?
If thats the case then they would be original to the cabinet I would say, the only strange thing is I can not out of all the numbers from your drivers that you listed match a manufactuer code and thats what`s strange!
In the era that your amp was made Kustom used CTS or Eminence made drivers and they would have number string starting with 137 and a space, or 67 and a space, for example 137 7545 which would be a CTS made driver from the 45th week of 1975.

Report message to a moderator

Re: Lead III/IV Speakers [message #18136 is a reply to message #18129]

Mon, 04 February 2013 11:46

Kochens
Messages: 80
Registered: April 2009
Location: Denmark

Member

Do you not like the sound of the speakers?

Report message to a moderator

Re: Lead III/IV Speakers [message #18137 is a reply to message #18129]

Mon, 04 February 2013 12:43

benn
Messages: 11
Registered: February 2013

Junior Member

As promised, here are some pictures, including a photo of the front where those conspicuous center voice coil covers are visible. Thanks for all the help so far folks!

http://img.photobucket.com/albums/v401/vivalaben1/778524816_2765221857_764459882_1360002609953.jpeg

http://img.photobucket.com/albums/v401/vivalaben1/778525042_2765222606_764460109_1360002625922-Copy.jpeg

http://img.photobucket.com/albums/v401/vivalaben1/778525133_2765222900_764460197_1360002659014.jpeg

http://img.photobucket.com/albums/v401/vivalaben1/778525441_2765223923_0-Copy.jpeg

http://img.photobucket.com/albums/v401/vivalaben1/778525312_2765223490_764460375_1360002646335-Copy.jpeg

[Updated on: Fri, 08 March 2013 10:31]

Report message to a moderator

Re: Lead III/IV Speakers [message #18138 is a reply to message #18137]

Mon, 04 February 2013 13:23

Kustom_Bart
Messages: 601
Registered: October 2010
Location: Greenville, MichiGUN

Senior Member

The links no worky Smile

Smile

Report message to a moderator

Re: Lead III/IV Speakers [message #18139 is a reply to message #18129]

Mon, 04 February 2013 13:35

benn
Messages: 11
Registered: February 2013

Junior Member

Fixed!

Report message to a moderator

Re: Lead III/IV Speakers [message #18140 is a reply to message #18129]

Mon, 04 February 2013 14:38

chicagobill
Messages: 2006
Registered: April 2003

Senior Member

Could the last number be 2858014?

285 was Rola speakers.

Report message to a moderator

Re: Lead III/IV Speakers [message #18141 is a reply to message #18129]

Mon, 04 February 2013 15:16

benn
Messages: 11
Registered: February 2013

Junior Member

It is a 2, you're right! Not sure why I was focusing my attention on the speaker with the most smudged out stamp, but the code is in fact 2858014. Can anyone make any sense of THAT code? Made in the 14th week of 1980 or something like that?

Report message to a moderator

Re: Lead III/IV Speakers [message #18142 is a reply to message #18129]

Mon, 04 February 2013 15:54

benn
Messages: 11
Registered: February 2013

Junior Member

Other thoughts on the cab/speakers now that you've got me going: LOUD! I just A/B'd this cab with my G12T-75 Ampeg cab (Marshall 1960 clone - plywood construction) and it definitely has the edge on volume (though I would have assumed these speakers are far less sensitive than the G12T-75). The bass is also bigger coming out of this cab, particularly on the lower strings, but not quite as tight as the G12T-75s.

[Updated on: Fri, 08 March 2013 10:32]

Report message to a moderator

Re: Lead III/IV Speakers [message #18143 is a reply to message #18129]

Mon, 04 February 2013 16:39

Kochens
Messages: 80
Registered: April 2009
Location: Denmark

Member

The lll-lV Lead cabs where not made for high gain amps. I have a` 4x12 ported cab and I love it(copy of a lV lead) with 2 celestion vintage 30 and 2 G12H and the sound are:+++++++++++GREAT for ROCK.

[Updated on: Mon, 04 February 2013 16:41]

Report message to a moderator

Re: Lead III/IV Speakers [message #18144 is a reply to message #18143]

Mon, 04 February 2013 17:46

pleat
Messages: 1454
Registered: June 2004
Location: Belding, Mi

Senior Member

Keep in mind that the Kustom cab is a 4 ohm cabinet. Not sure what the impedance of the other cabinet is, so if the other cab is an 8 ohm cab, the kustom will sound louder.
One thing I'd check is make sure all the nuts are tight that hold the speakers in, also maybe add some insullation. Kustom was trying to cut costs, which is one reason the MDF construction rather than full plywood as the earlier cabs were built.
pleat

Report message to a moderator

Re: Lead III/IV Speakers [message #18145 is a reply to message #18129]

Mon, 04 February 2013 18:09

benn
Messages: 11
Registered: February 2013

Junior Member

I've never insulated a cab - will doing so tighten up the sound? Also, will it lower the volume? Because I actually like how much air this thing moves so that may be a concern. Also, the Ampeg cab I compared this one to is 4 ohms as well.

Report message to a moderator

Re: Lead III/IV Speakers [message #18148 is a reply to message #18129]

Tue, 05 February 2013 09:54

stevem
Messages: 4775
Registered: June 2004
Location: NY

Senior Member

What amp head are you pumping thru the cabinet?
If its a head with a tube output stage they always sound best when running them at their highest Impeadance as only then are you using the full secondary winding of the Output transformer.
On a multi taped output transformer for example the 16 ohm tap is the full winding, the 8 ohm tap uses 1/3 less of the winding and the 4 ohm tap uses only one half the winding.
Its kind of the same thing as if you put wide tires on your car for better handling, but you pumped them up with so much air that only half the tires tread width was in contact with the road.
Also if those Kustom/Rola speakers are well used then the surround and spider parts of the speaker may be allowing the cone to move too freely and be slow to return to its static postion. This will make for overly powerfull lows and what you precive as shadowed highs.
A way to test this is to plug a cable into the cabinet and hold a new 9 volt batter across the plug, in doing this you should jsut be able to see the speaker cones move.
If the cone travel seen aprocess 1/4" they are well played and need reconing.

Report message to a moderator

Re: Lead III/IV Speakers [message #18149 is a reply to message #18148]

Tue, 05 February 2013 11:32

Kustom_Bart
Messages: 601
Registered: October 2010
Location: Greenville, MichiGUN

Senior Member

What Steve is saying is if the surrounds are beaten up, it is like bad shocks on a car and you would at least need new surrounds installed, but for the price, you are better off to have them re-coned and then you know that they are all good for a very long time.

Report message to a moderator

Re: Lead III/IV Speakers [message #18150 is a reply to message #18129]

Tue, 05 February 2013 17:55

benn
Messages: 11
Registered: February 2013

Junior Member

I'm running a Peavey VTX Classic combo through the cab. I'm using the combo's speakers and have the Kustom running from the external speaker jack. The amp is 4 ohms with the internal speakers and switches to a 2 ohm tap with a plug in the external speaker jack, so altogether I'm running the 4 ohm internal and 4 ohm Kustom together at 2 ohms.

I tried the battery trick -cool test, but I don't think the cones were moving particularly far. I also tried a bit of insulation in the cab. It did tighten the bass, but also flattened out the sound a little. I will keep experimenting with this thing. Thanks for all the help!

[Updated on: Tue, 05 February 2013 17:56]

Report message to a moderator

Previous Topic:	My Amp's Almost as Old as Me- I Think...
Next Topic:	Information

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Tue Nov 19 06:10:04 EST 2024