VintageKustom.com: Repairing Kustom Amps

Home » VintageKustom.com » Repairing Kustom Amps » Schematic Accuracy (Missing components)

Show: Today's Messages :: Polls :: Message Navigator

Re: Schematic Accuracy [message #20122 is a reply to message #20097]

Thu, 13 February 2014 13:57

bluezebra
Messages: 89
Registered: February 2014
Location: Lafayette, LA

Member

Hi Bill
Thanks for your input.
Maybe I didn't explain it well enough about the transistors on the schematic as Q124 Q125 They are both labeled with BOTH numbers as 2N4249 and RCA 38734. Is this suggesting that both are acceptable?
I'm looking for a picture of the board since there are three components on this board NOT listed on the schematic. ie..Q131 is listed on the schematic but not listed in the transistor location diagram and not found on the board. I have a .1 100volt ceramic cap that is not listed but is on the board....strangely found clipped on one side.

I'm still trying to identify why the +8 is uneven. The schematic shows different resistor values in that section of the circuit. At last measurement it is +10.7 and -9.9. I installed the old rectifier and old wires and the mains are still +40.5 and -40.4

Report message to a moderator

[Message index]

		Schematic Accuracy By: bluezebra on Mon, 10 February 2014 01:29
		Re: Schematic Accuracy By: stevem on Mon, 10 February 2014 06:30
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 10:19
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 10:26
		Re: Schematic Accuracy By: chicagobill on Mon, 10 February 2014 12:40
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 13:00
		Re: Schematic Accuracy By: stevem on Mon, 10 February 2014 13:17
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 13:41
		Re: Schematic Accuracy By: chicagobill on Mon, 10 February 2014 16:24
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 17:10
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 17:33
		Re: Schematic Accuracy By: chicagobill on Tue, 11 February 2014 12:22
		Re: Schematic Accuracy By: bluezebra on Tue, 11 February 2014 13:25
		Re: Schematic Accuracy By: stevem on Wed, 12 February 2014 09:26
		Re: Schematic Accuracy By: bluezebra on Wed, 12 February 2014 12:55
		Re: Schematic Accuracy By: stevem on Wed, 12 February 2014 17:08
		Re: Schematic Accuracy By: bluezebra on Wed, 12 February 2014 17:20
		Re: Schematic Accuracy By: bluezebra on Wed, 12 February 2014 21:22
		Re: Schematic Accuracy By: chicagobill on Thu, 13 February 2014 10:43
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 13:57
		Re: Schematic Accuracy By: chicagobill on Thu, 13 February 2014 14:40
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 15:20
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 15:25
		Re: Schematic Accuracy By: chicagobill on Thu, 13 February 2014 16:14
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 17:39
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 19:36
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 22:03
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 22:40
		Re: Schematic Accuracy By: chicagobill on Fri, 14 February 2014 13:04
		Re: Schematic Accuracy By: bluezebra on Fri, 14 February 2014 22:38
		Re: Schematic Accuracy By: stevem on Sat, 15 February 2014 07:43
		Re: Schematic Accuracy By: bluezebra on Sat, 15 February 2014 10:28
		Re: Schematic Accuracy By: bluezebra on Sat, 15 February 2014 12:11
		Re: Schematic Accuracy By: stevem on Mon, 17 February 2014 06:33
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 11:07
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 11:33
		Re: Schematic Accuracy By: chicagobill on Mon, 17 February 2014 13:25
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 14:20
		Re: Schematic Accuracy By: chicagobill on Mon, 17 February 2014 14:54
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 16:56
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 17:14
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 17:36
		Re: Schematic Accuracy By: chicagobill on Tue, 18 February 2014 12:24
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 13:31
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 13:37
		Re: Schematic Accuracy By: chicagobill on Tue, 18 February 2014 13:58
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 18:25
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 20:53
		Re: Schematic Accuracy By: chicagobill on Tue, 18 February 2014 21:38
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 23:15
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 23:17
		Re: Schematic Accuracy By: chicagobill on Wed, 19 February 2014 01:44
		Re: Schematic Accuracy By: bluezebra on Wed, 19 February 2014 10:32
		Re: Schematic Accuracy By: chicagobill on Wed, 19 February 2014 11:13
		Re: Schematic Accuracy By: bluezebra on Wed, 19 February 2014 12:21
		Re: Schematic Accuracy By: chicagobill on Wed, 19 February 2014 13:20
		Re: Schematic Accuracy By: bluezebra on Wed, 19 February 2014 14:02
		Re: Schematic Accuracy By: bluezebra on Wed, 19 February 2014 14:05
		Re: Schematic Accuracy By: chicagobill on Wed, 19 February 2014 17:06
		Re: Schematic Accuracy By: bluezebra on Wed, 19 February 2014 23:21
		Re: Schematic Accuracy By: stevem on Thu, 20 February 2014 06:49
		Re: Schematic Accuracy By: bluezebra on Thu, 20 February 2014 12:03

Previous Topic:	Kustom Studio 2 Valve head with fried board
Next Topic:	footswitch K200A PA

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Wed Jul 03 09:32:01 EDT 2024