VintageKustom.com: Comment Board

Home » VintageKustom.com » Comment Board » 1G+1H cab (Good for guitar?)

Show: Today's Messages :: Polls :: Message Navigator

1G+1H cab [message #17699]

Sat, 17 November 2012 12:28

kustomhead
Messages: 121
Registered: April 2012
Location: Redding, Ca

Senior Member

I've got a line on a 1G+1H cab and would like to know is that an 8 ohm cab and do they sound good for guitar? I have a K150-2 head. Thanks, Jim

Report message to a moderator

Re: 1G+1H cab [message #17703 is a reply to message #17699]

Sat, 17 November 2012 14:46

Kustom_Bart
Messages: 601
Registered: October 2010
Location: Greenville, MichiGUN

Senior Member

I have a pair of them that I use for PA mains, but have plugged a guitar into one and they sound great for guitar. It is really a full range cab. Back at the time they were built they used 15" speakers for guitar and not 12" speakers. The name 1G 1H makes it a guitar cab by Kustom. They sound good, I forget where the horn crosses, but ChicagoBill or Pleat will know for sure, I just can't recall.

Good Luck

Report message to a moderator

Re: 1G+1H cab [message #17713 is a reply to message #17703]

Sun, 18 November 2012 12:18

kustomhead
Messages: 121
Registered: April 2012
Location: Redding, Ca

Senior Member

Is the K150 version 8 ohms?

Report message to a moderator

Re: 1G+1H cab [message #17714 is a reply to message #17699]

Sun, 18 November 2012 12:35

Kustom_Bart
Messages: 601
Registered: October 2010
Location: Greenville, MichiGUN

Senior Member

The 1G 1H cabs stock were 8 ohm originally. Mine have KEI speakers in them.

Report message to a moderator

Re: 1G+1H cab [message #17716 is a reply to message #17714]

Sun, 18 November 2012 15:21

kustomhead
Messages: 121
Registered: April 2012
Location: Redding, Ca

Senior Member

Thanks so much for answering all my questions!I love vintage Kustom stuff like we all do and this site is awesome!

Report message to a moderator

Re: 1G+1H cab [message #17725 is a reply to message #17716]

Mon, 19 November 2012 19:02

pleat
Messages: 1454
Registered: June 2004
Location: Belding, Mi

Senior Member

If your crossover cap is 10uf makes the horn cross at just under 2K Hz. As far as a good sounding cabinet, it really depends on what you like to hear. I personally think the horns are quite brittle especially with distortion. You can change the crossover cap to a 4uf and that will raise the crossover to 5K which will let more tone go to the 15" before the horn kicks in.
Another site you might like is http://www.kustomcollector.com/index.html

pleat

Report message to a moderator

Re: 1G+1H cab [message #17727 is a reply to message #17725]

Tue, 20 November 2012 00:58

kustomhead
Messages: 121
Registered: April 2012
Location: Redding, Ca

Senior Member

Is the 15" speaker 8 ohm?

Report message to a moderator

Re: 1G+1H cab [message #17728 is a reply to message #17699]

Tue, 20 November 2012 01:41

Kustom_Bart
Messages: 601
Registered: October 2010
Location: Greenville, MichiGUN

Senior Member

Yes it is, if it is stock. As well as the horn, but it is still only a 8 ohm cab because the horn value doesn't count as it isn't up there long enough to make it 4 ohms.

[Updated on: Tue, 20 November 2012 01:48]

Report message to a moderator

Re: 1G+1H cab [message #17729 is a reply to message #17728]

Tue, 20 November 2012 08:54

pleat
Messages: 1454
Registered: June 2004
Location: Belding, Mi

Senior Member

According to my chart, the 1G+H cabinet uses an 8 ohm speaker and 16 ohm horn driver, wired in paralell and total impedence of the cab is 8 ohms.
pleat

Report message to a moderator

Re: 1G+1H cab [message #17731 is a reply to message #17699]

Tue, 20 November 2012 11:47

Kustom_Bart
Messages: 601
Registered: October 2010
Location: Greenville, MichiGUN

Senior Member

Mine must have been replaced as they say 8 ohm on them, but that wouldn't surprise me.

Report message to a moderator

Re: 1G+1H cab [message #17775 is a reply to message #17725]

Thu, 29 November 2012 20:01

kustomhead
Messages: 121
Registered: April 2012
Location: Redding, Ca

Senior Member

All I see is a wire saying F1 Beldon from the + post on the horn to another terminal on the horn. Is this the 10uf cap wire? The cab is mint and was never opened before so it must be stock. I have a 5uf cap, will that do the trick?

Report message to a moderator

Previous Topic:	PRICE
Next Topic:	My first Custom and way cool new here and I have a few questions if i may?

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Tue Nov 19 13:41:55 EST 2024