VintageKustom.com: Repairing Kustom Amps » Kustom Organ Effects Loop

Home » VintageKustom.com » Repairing Kustom Amps » Kustom Organ Effects Loop (How to create an effects loop in a Kutsom Combo Organ)

Show: Today's Messages :: Polls :: Message Navigator

Kustom Organ Effects Loop [message #27152]

Sun, 06 January 2019 17:31

Sahara
Messages: 3
Registered: January 2019

Junior Member

Hi. I have an early (#1048) Kombo organ in great shape and I would like to install an effects loop. Is this as easy as tapping into the blue and black wires coming off the keyboard?

Report message to a moderator

Re: Kustom Organ Effects Loop [message #27154 is a reply to message #27152]

Mon, 07 January 2019 12:07

stevem
Messages: 4773
Registered: June 2004
Location: NY

Senior Member

If you go into this sites tech section and pull up the schematic for the combo or organ, then go to page 9 and on the lower right side above the info box you will see the output marked as " to power amp"
This is where you want to break the signal chain open which is this hot lead so to speak and install a jack on each end.
Your ground for each jack will be the chassis.

[Updated on: Mon, 07 January 2019 12:24]

Report message to a moderator

Re: Kustom Organ Effects Loop [message #27156 is a reply to message #27154]

Mon, 07 January 2019 15:08

Sahara
Messages: 3
Registered: January 2019

Junior Member

Thank you, Steve! I'll have a look.

Report message to a moderator

Re: Kustom Organ Effects Loop [message #27157 is a reply to message #27154]

Mon, 07 January 2019 16:10

Sahara
Messages: 3
Registered: January 2019

Junior Member

Steve's suggestion of following the schematic worked! Here's how to add an effects loop to a Kustom Kombo organ...The place to tap into the audio output is at the expression pedal. There is a thin single wire (mine is red) going from the expression pedal to the amp. Simply cut the wire and add either a female 1/4" to each wire or, alternatively, a guitar cable, to each end with the ground attaching to the chassis. I don't use the accessory preamp so I'm going to use the holes where the input jacks are now with 1/4 " female jacks going to the loop circuit. This will be a convenient place to plug in the effects without making any new holes. The old jacks will simply be unscrewed and tie wrapped behind the preamp panel. If you don't want to use the loop, remember to jump the jacks with a short cable. I just tried the loop with a digital delay and it's awesome. I can only imagine how this will sound with a Leslie simulator ( I see a Neo Vent in my future) pumping through those JBLs! Kudos to Steve for pointing me in the right direction!

Report message to a moderator

Re: Kustom Organ Effects Loop [message #27158 is a reply to message #27152]

Tue, 08 January 2019 06:02

stevem
Messages: 4773
Registered: June 2004
Location: NY

Senior Member

Good to hear your golden and always happy to be of help!

Report message to a moderator

Re: Kustom Organ Effects Loop [message #27159 is a reply to message #27152]

Tue, 08 January 2019 09:48

rodak
Messages: 516
Registered: October 2001
Location: Georgia

Senior Member

Thanks! I'll share this with my combo organ group, too. Seems pretty simple, but it's always nice to hear of someone successfully implementing such a thing.

www.combo-organ.com

Report message to a moderator

Previous Topic:	Kustom 100 issues
Next Topic:	K200B DC voltage on speaker repair

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Thu Oct 31 11:21:17 EDT 2024