| What to connect Kustom K250-4 [message #9230] |
Thu, 14 February 2008 11:11  |
frans
Messages: 6
Registered: February 2008
|
Junior Member |
|
|
What can y connect to " To Module Input" at the backside of my amp.
And I am looking to the specs of these amp.
Greetings
Frans
Holland
|
|
|
|
|
|
|
|
| Re: What to connect Kustom K250-4 [message #9233 is a reply to message #9232] |
Fri, 15 February 2008 10:47  |
chicagobill
Messages: 2006
Registered: April 2003
|
Senior Member |
|
|
Weclome to the board Frans.
Yes you can use more then one cabinet as long as the total load stays around 3-4 ohms. Anything less, and you may overheat the power amp. I believe that your amp has 2 speaker jacks on the back.
As for the "Module" output, this is a low level signal and not a speaker output. It is for driving the input of a power amp. Back in the 70's Kustom made speaker cabinets with built in power amps that could be added to your system to increase the total power/watts of output. This way you could control 2, 3 or 10, 100watt amps from one control panel (head).
Again, welcome!
|
|
|
|
|
|
| Re: What to connect Kustom K250-4 [message #9235 is a reply to message #9234] |
Fri, 15 February 2008 18:08 |
chicagobill
Messages: 2006
Registered: April 2003
|
Senior Member |
|
|
So does that make you a "Howling Hotdog?
As for your speaker question, we need to know how your 2-15 cabinet is wired. Do you have access to an ohmmeter? If you do, read the dc resistance of the speaker cabinet. It could be somewhere around 16 ohms or 8 ohms or 4 ohms.
Let us know.
|
|
|
|
| Re: What to connect Kustom K250-4 [message #9236 is a reply to message #9230] |
Mon, 18 February 2008 06:28 |
stevem
Messages: 4773
Registered: June 2004
Location: NY
|
Senior Member |
|
|
Some added detail for you when you check the cabinets.
A 16 ohm cabinet will test out above 8 ohms but less than 16 ohms.
A 8 ohm cabinet will test under 8 ohms, but over 4 ohms, and 4 ohms, I think you get the pattern.
If your 2-15" cab has the original speakers it will be a 4 or 8 ohm cabinet.
If its 8 ohms you are set, all you have to do is Y the Kustom and the Fender cabinet together, in fact I think the Fender cab as two jacks so you can just plug the head into the fender cab first, and then run another speaker cable to the 2-15" cab.
This will be a 4 ohm load and the 250 head will output its full wattage witha 3 to 4 ohm load.
If the 2-15" kustom cab turns out to be 4 ohm, you can still use the Fender and the Kustom cabinet, but you will have to make up a cable to run them in serise not in parallel like I discribed before.
With this wiring the 4 ohm (Kustom cabinet) will be getting twice the wattage as the fender due its its lower resistance, and as such may seem a little louder than the Fender, but since the Fender has 2 more speakers I will guess that with its added spl level they will both seem to be just as loud as each other.
With the serise wiring the Kustom will only be able to output about 80 watts RMS, not its 100 or more watts, but the added 4 speakers will well more than make up for it!
|
|
|
|
|
|
VintageKustom.com
Search
Help
Members
Register
Login
Home
]