k200b1 keeps blowing fuses [message #11705] |
Sun, 30 August 2009 18:39 ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
JLElectric
Messages: 12 Registered: August 2009 Location: Holly Ridge, NC
|
Junior Member |
|
|
k200b1 keeps blowing the fuse by the on/off switch. I install 2 eminence 8 ohm 15's in cabinet, it played great for about thirty min. Then keeps blowing fuses. The amp hasnt been used in a while. Is there an easy fix?
|
|
|
|
Re: k200b1 keeps blowing fuses [message #11707 is a reply to message #11706] |
Mon, 31 August 2009 08:04 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
JLElectric
Messages: 12 Registered: August 2009 Location: Holly Ridge, NC
|
Junior Member |
|
|
i will try that. It blows as soon as i flip the switch but maybe i can tell. What is the part called from radioshack. Im gonna go ahead and pick it up. Thanks for the help. Im sure i will have more questions.
|
|
|
Re: k200b1 keeps blowing fuses [message #11709 is a reply to message #11705] |
Mon, 31 August 2009 11:59 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
chicagobill
Messages: 2005 Registered: April 2003
|
Senior Member |
|
|
If the amp is instantly blowing the fuse, I doubt that you will be able to get an accurate voltmeter indication on the output jack.
As Steve noted, there are two main causes for your problem. One is a shorted output transistor, and the other is a shorted rectifier in the power supply. There can be other causes, but these are the two usual suspects.
You can just replace parts with the hope that you will find the right one, or you can troubleshoot the circuit to find your problem. Either way works.
If you have a multimeter (especially one with a diode test function), you can check the outputs and the rectifiers before you start spending money on parts or additional fuses.
If you don't have a meter, there are a couple of ways to find the problem, but it may take a few fuses to figure it out.
|
|
|
|
Re: k200b1 keeps blowing fuses [message #11711 is a reply to message #11710] |
Mon, 31 August 2009 12:36 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
JLElectric
Messages: 12 Registered: August 2009 Location: Holly Ridge, NC
|
Junior Member |
|
|
you are right, im lost. Im an electrician, but electronics is totally different. I will try that. I did try unplugging the output transistors before and it still blew. I will try the rectifier when i get home. Thanks
|
|
|
Re: k200b1 keeps blowing fuses [message #11715 is a reply to message #11705] |
Mon, 31 August 2009 16:25 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
JLElectric
Messages: 12 Registered: August 2009 Location: Holly Ridge, NC
|
Junior Member |
|
|
I unhooked the red and green on the rectifier and the fuse still blew quickly. Should I continue or take it somewhere? Could it be the transistors and drivers?
|
|
|
Re: k200b1 keeps blowing fuses [message #11716 is a reply to message #11715] |
Mon, 31 August 2009 17:47 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
chicagobill
Messages: 2005 Registered: April 2003
|
Senior Member |
|
|
JLElectric:
Try pulling off the two wires that go from the transformer to the rectifier, make sure that they are away from each other and anything else. Now if the fuse still blows, the transformer may be shorted. (It could also be a problem with the wiring.) If the fuse holds, then the rectifier is shorted and needs to be replaced.
Steve:
The green wire from the rectifier supplies the negative voltage bus and is not grounded. After pulling off the red and green wires, if the fuse still blows, it does not mean that the rectifier is ok. Just the opposite, it means that the problem lies in the rectifier or the power transformer.
|
|
|
Re: k200b1 keeps blowing fuses [message #11719 is a reply to message #11716] |
Mon, 31 August 2009 19:53 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
JLElectric
Messages: 12 Registered: August 2009 Location: Holly Ridge, NC
|
Junior Member |
|
|
i did what you said, it didnt blow. So I changed out the rectifier. I spoke with my father in law and he said it sounds like it did before. Lack of drive or power. He actually thought it was blown speakers before. So I changed the speakers. Now it just needs some power. Whats my next step. It sounds really distorted. Could it be transistors?
|
|
|
|