VintageKustom.com
VintageKustom.com is your source for literature and information on the tuck-and-roll vintage Kustom amps from the 60's and 70's, as well as their related products such as guitars and organs . We provide a webboard for help with kustom gear history, technical information and repairs as well as discussions with other collectors.

Home » Classified Ads » Wanted » licon switch 01-740122
Show: Today's Messages :: Polls :: Message Navigator
Switch to threaded view of this topic Create a new topic Submit Reply
licon switch 01-740122 [message #20048] Fri, 24 January 2014 08:35 Go to next message
philrouge is currently offline  philrouge
Messages: 7
Registered: January 2014
Location: France
Junior Member
Hi,
I need a licon switch 01-740122 for my K-150 head. Mine is broken, I have to replace it, it is the illuminated blue power switch.
If you have one of these for selling, please email me at philrouge77@gmail.com
Thanks !
Phil
Re: licon switch 01-740122 [message #20265 is a reply to message #20048] Fri, 07 March 2014 11:40 Go to previous messageGo to next message
eldoryder is currently offline  eldoryder
Messages: 5
Registered: March 2014
Location: Nacogdoches, TX
Junior Member
Hi Phil-

You and me BOTH! I also need a LICON 01-740122 switch! If you do find a source (or if someone sees yours and replies first), please let me know also! I would buy either NOS or good working USED. Thanks!


Mike Selvey
Nacogdoches, TX
eldoryder@yahoo.com
936-371-9031


FROM DEEP BEHIND THE PINE CURTAIN OF EAST TEXAS!!!!
Re: licon switch 01-740122 [message #20284 is a reply to message #20265] Sat, 08 March 2014 09:50 Go to previous messageGo to next message
philrouge is currently offline  philrouge
Messages: 7
Registered: January 2014
Location: France
Junior Member
hi Mike,
of course, if I can find any spare licon switches, I'll tell you about it. But I have been searching, and it seems there's no more of them anywhere. And it is perhaps more tricky to find one in France.
We just have to wait until a new old stock of these appears on eBay... maybe one day.
So if you find a source, let me know too !
I have repaired mine (thanks to Stevem's advices) it works almost perfectly, but I think one of these days I will have to replace it for a completely different one.
Regards
Phil

Re: licon switch 01-740122 [message #20289 is a reply to message #20284] Sat, 08 March 2014 21:21 Go to previous messageGo to next message
Kustom_Bart is currently offline  Kustom_Bart
Messages: 601
Registered: October 2010
Location: Greenville, MichiGUN
Senior Member
You are better off to buy a doaner head or amp that is trashed or beyond repair or the naugahyde is to far gone that has a good switch.
Re: licon switch 01-740122 [message #20291 is a reply to message #20289] Sun, 09 March 2014 06:31 Go to previous messageGo to next message
philrouge is currently offline  philrouge
Messages: 7
Registered: January 2014
Location: France
Junior Member
This is a good idea, but maybe not so easy to find for a low price...
Re: licon switch 01-740122 [message #20294 is a reply to message #20291] Sun, 09 March 2014 07:37 Go to previous messageGo to next message
C4ster
Messages: 686
Registered: June 2001
Location: Mukwonago, WI (Milwaukee...
Senior Member
Hi guys, It's been a long time since I've commented here but I also have acquired a K300 PA with missing switches. After reading about this, I found this link. I am not in a position to measure the dimensions of the original Licon switch, but this might be a suitable replacement. http://www.e-switch.com/product/tabid/96/productid/51/sename /d16-series-illuminated-pushbutton-switches/default.aspx#ex1
See what you think. Kind of like the old purple Kustom (Dialight) lights in the older series, you can get the switches with different lens colors, if you so desire. There is a PDF specification that you can download and it is very detailed with every option you can imagine. I think this would be a great replacement.
Conrad

[Updated on: Sun, 09 March 2014 08:04]

Report message to a moderator

Re: licon switch 01-740122 [message #20298 is a reply to message #20294] Sun, 09 March 2014 09:47 Go to previous messageGo to next message
philrouge is currently offline  philrouge
Messages: 7
Registered: January 2014
Location: France
Junior Member
Thanks for the link ! I think that's the kind of switch that could be a good replacement option. But I think there are 6 contacts on the original Licon instead of 4 here. So I guess it should be rewired in a different way.
Re: licon switch 01-740122 [message #20299 is a reply to message #20298] Sun, 09 March 2014 14:25 Go to previous messageGo to next message
C4ster
Messages: 686
Registered: June 2001
Location: Mukwonago, WI (Milwaukee...
Senior Member
Hi Phil,
First off, I would ground the chassis and eliminate the polarity reversal switch. That method of hum elimination has branded more guitarist's lips with the screen of a microphone than any other. E-switch also has a pilot light that looks exactly like the switch it compliments. I would put that in the polarity reversal switch hole and just wire it to light when the amp is on. The power switch only needs to be a SPST switch but E-switch only sells a SPDT switch. By removing the polarity switch, you only need to apply power to the transformer. I see that you are in France and usually mains switches are 2 pole, one for the "hot" and one for the "neutral". I looked at the diagrams at the bottom of the PDF and noticed that the switches are not actually a true SPDT configuration but a double acting switch that opens 2 contacts and closes 2 contacts when the switch is pressed. In France I would assume it would be best to use a DPDT switch. You would then use terminals 3 and 4 on each section for the black and white wires. I need some help from the guys who have the K150, K250, K300, K600 series amps as I have not had the opportunity to check out my newest acquisition. I'm mostly familiar with the K100, K200 series amps.
Conrad
Re: licon switch 01-740122 [message #20301 is a reply to message #20299] Mon, 10 March 2014 04:59 Go to previous messageGo to next message
philrouge is currently offline  philrouge
Messages: 7
Registered: January 2014
Location: France
Junior Member
Hi Conrad,
thanks for the details.
I have replaced the power cord for a three-wire and grounded the chassis. This was because I sometimes got little electric shocks and did not feel secure with it. Now it seems to be perfect. We commonly have the network wired with ground in France, I have put a ground wire everywhere in my house so this is not a problem, but of course this is not the same everywhere !
For the moment the power switch still works, it is broken inside but I have fixed it with a nylon strip to hold it in place.
Perhaps it will break one day, and this is why I am looking for a spare. But I will keep your informations safe for the day it will happen !
I did not have the opportunity to try several Kustom amps as they are pretty rare here, but I can say that my K-150-2 is probably the best solid state amp I've ever heard. I had a Lab series L7 combo that was really good but unfortunately it was stolen, and I own an old HH IC-100 that is good too, but to me the Kustom has a lot more attractive sound, the tremolo/vibrato is fantastic and the eq section is very effective and musical, the bass controls is really powerful, it can deliver tons of bottom end, and I am experimenting to use both channels simultaneously, so the eq section is really amazing. Unfortunately I do not have the original cab, but they seem so big and heavy, I'm happy with my 2x12 Engl cab loaded with Celestion V30.
Re: licon switch 01-740122 [message #27078 is a reply to message #20301] Fri, 26 October 2018 21:02 Go to previous messageGo to next message
philrouge is currently offline  philrouge
Messages: 7
Registered: January 2014
Location: France
Junior Member
Hi guys ! It's been a long time since I wrote my last message here. I'm still searching for the licon switch and I have put an automatic search on ebay. Here's what I found today :
h t t p s://www.ebay.fr/itm/LOT-OF-TWO-01-740081-LICON-SWITCH-PUSHBU TTON-FULL-SIZE/142953303356?hash=item2148ae4d3c:g:1AMAAOSw0I tbq-Ri:rk:2:pf:0
The part number is not exactly the same (01-74081 instead of 01-74122) but it looks VERY close to the Kustom power/polarity switches. I wonder if this one could work as a spare (I will have to find the lightbulbs too).
If someone could tell me if it's good (the switches are quite cheap but the shipping is very expensive: 23 USD !!!) so I need to be sure before I spend the money.
Maybe this could help Mike, if he's still searching too...
Thanks a lot if you can answer !
Smile
Phil
(I have changed the beginning of the link because "I cannot use links until I have posted more than 10 messages" so please remove spaces I have placed at the beginning of the URL...)
Re: licon switch 01-740122 [message #27079 is a reply to message #20048] Sat, 27 October 2018 06:10 Go to previous message
stevem is currently offline  stevem
Messages: 4774
Registered: June 2004
Location: NY
Senior Member
Hi guys!
I have switches that will work, they are not 100% original looking but very close.
95 % of the time you can fix your old busted switch without even picking up a soldering iron, all you need are 2 cable ties.
Call me if you want to try this repair first as my replacement switches are not cheap at 70 bucks, but I guess there cheaper then buying a donor amp!

Steve 914 420 4356
  Switch to threaded view of this topic Create a new topic Submit Reply
Previous Topic: Looking for a 2x15 T&R cabinet
Next Topic: Blue 3x15 Cabinet
Goto Forum:
  

-=] Back to Top [=-
[ Syndicate this forum (XML) ] [ RSS ]

Current Time: Wed Nov 06 00:52:37 EST 2024