Castors [message #25269] |
Fri, 22 July 2016 23:43 ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
slk854
Messages: 192 Registered: January 2015
|
Senior Member |
|
|
Just out of curiosity, has anyone ever tried to put ball bearings back in the castors? Yes I am aware that new castors can be had. I just installed new ones on a cab, but have two old ones that have lost all the ball bearings. I just like to tinker with things. I am assuming there are 2 sets of bearings in each wheel upper and lower. I was thinking of using BB's, and loading them in. Anyone ever try????
Steve
|
|
|
Re: Castors [message #25273 is a reply to message #25269] |
Sat, 23 July 2016 06:11 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
stevem
Messages: 4759 Registered: June 2004 Location: NY
|
Senior Member |
|
|
The original casters are crimped together in a big hydro press once the the ball bearings are loaded in, I guess if you have a bunch of free time on your hands you can screw with , but I would not and a love to fix things when I can!
The only hope would be to grind the crimp off then drill and tap the shank to take a bolt and a big enough washer to hold / crimp the top to the bottom section again.
Brass BBs by the way are very soft so even if you get them in they will go out of round even before they ware down!
[Updated on: Sat, 23 July 2016 06:14] Report message to a moderator
|
|
|
|
Re: Castors [message #25283 is a reply to message #25274] |
Mon, 25 July 2016 08:02 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
C4ster
Messages: 686 Registered: June 2001 Location: Mukwonago, WI (Milwaukee...
|
Senior Member |
|
|
Steve is right but an added issue is the actual roundness of the balls. Besides the diameter of the balls is/are VERY important to fit into the race without binding. Besides, the cost is not extremely high. This is still an inexpensive hobby, compared to: Cars, horses, airplanes, golf! You get the picture.
Conrad
|
|
|
|
Re: Castors [message #25285 is a reply to message #25284] |
Mon, 25 July 2016 10:43 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
C4ster
Messages: 686 Registered: June 2001 Location: Mukwonago, WI (Milwaukee...
|
Senior Member |
|
|
That reply was mostly tongue in cheek. I'm like you, spend more time and effort fixing something rather than replacing it. The delight and pride one gets from saving an item from the trash is worth the effort. Only to have someone who can't, shrug their shoulders and say "so?" Even that is worth the effort.
Conrad
|
|
|
Re: Castors [message #25286 is a reply to message #25269] |
Mon, 25 July 2016 11:33 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) |
slk854
Messages: 192 Registered: January 2015
|
Senior Member |
|
|
Looks like we are neighbors. I am in Elk River, MN
One other thing I did once was to repair a knob on the amp face. It was missing the metal insert so I took a 3/8" hole punch and punched out a round piece out of a beer can. Took a 1/4" dowel with laping polish and it shined it up really good and glued it in and you can't tell which one it was now. Yep a new knob only cost a couple of bucks but this was free, and I got satisfaction. I figure as long as you enjoy what you are doing life is good.
Steve
|
|
|