Repairing Kustom 200 4 CH PA head [message #28014] |
Wed, 10 February 2021 15:16 ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
alan_smythee
Messages: 3 Registered: February 2021
|
Junior Member |
|
|
Hi, everyone. This is my first post, so thank you for reading. I purchased a gold sparkle tuck-n-roll Kustom 200 4-ch PA head in the late 90s and used it periodically over the course of 5 years. I noticed that it started to make loud popping sounds after it was on for a few minutes, and the sound didn't seem to be impacted by a signal going into the amp. I'd like to repair it, and I'm wondering if anyone could provide some guidance as to how to best diagnose the issue. Friends have suggested that it's likely the filter caps, but I don't know for sure. I'm not a professional tech (obviously), but I have a soldering station, a multimeter, and some other basic tools. I'm hoping this is something I can do myself because I think the cost of a repair is greater than the value of the amp itself. Any guidance is very much appreciated. Thanks.
|
|
|
Re: Repairing Kustom 200 4 CH PA head [message #28017 is a reply to message #28014] |
Thu, 11 February 2021 07:37 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
stevem
Messages: 4769 Registered: June 2004 Location: NY
|
Senior Member |
|
|
Hello and welcome!
As a new member you will have to make 5 post that I will need to approve before post you make to this site just go right up, so don't think there is something wrong with the site.
First off I am assuming you have a K200B series amp, and not the A series?
Ok , on to your K200B-5 amp!
This issue it has must be tracked down by process of elimination.
The amp has 6 boards in it .
One of every channel on the face of the amp, a reverb board on the floor of the amp and a power supply / output driver board on the rear wall of the amp.
Any of these could be the cause of your issue
Slide the amp out of its case by removing the four 10/32 machine screws on the bottom of the amp.
Next note the small Differnt color wires running around the amp, these wires are what carry the audio signal from board to board within the amp, and these are what we will be disconnecting to go thru the process of elimination.
If you go to this site's technical section you can see the board layout and note the different colors of these wires labeled output going from board to board.
Post back when you have the amp out and have looked it over for these colored output wires and we will continue.
Can you read schematics?
[Updated on: Thu, 11 February 2021 08:08] Report message to a moderator
|
|
|
|
Re: Repairing Kustom 200 4 CH PA head [message #28026 is a reply to message #28014] |
Mon, 15 February 2021 01:48 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) ![Go to next message Go to next message](/FUDforum/theme/vk30/images/down.png) |
Cody UNO
Messages: 35 Registered: February 2021
|
Member |
|
|
Hey,
I literally drove 7 hours (14 hours total) to Arkansas yesterday from New Orleans to get a... wait for it... gold 100 4-channel PA head that the guy bought in the nineties. Is this Jeff? LMAO.
Mine actually has a different issue that I am about to leave a post about, but I wanted to reply because of the coincidence. Hopefully, we can both get ours rockin' and (tuck 'n') rollin' again ASAP.
[Updated on: Mon, 15 February 2021 02:08] Report message to a moderator
|
|
|
|
|
Re: Repairing Kustom 200 4 CH PA head [message #28042 is a reply to message #28014] |
Sun, 21 February 2021 04:39 ![Go to previous message Go to previous message](/FUDforum/theme/vk30/images/up.png) |
Cody UNO
Messages: 35 Registered: February 2021
|
Member |
|
|
I bought a cascade K200 PA head today and even with the reverb turned completely off it sounds like there is some sort of tail/reverb. I thought my ears were playing tricks on me at first so I plugged into my K100 PA head and it didn't do that at all. Hoping it's just user error on my part because the guy I bought it from had it restored with a 3-prong and a full inspection.
[Updated on: Sun, 21 February 2021 04:39] Report message to a moderator
|
|
|