VintageKustom.com: Repairing Kustom Amps » Help needed to troubleshoot Kustom PA 200 Channels

Home » VintageKustom.com » Repairing Kustom Amps » Help needed to troubleshoot Kustom PA 200 Channels (kustom 200 PA Repair)

Show: Today's Messages :: Polls :: Message Navigator

Help needed to troubleshoot Kustom PA 200 Channels [message #25647]

Mon, 17 October 2016 19:35

bproctor
Messages: 11
Registered: December 2015
Location: BOSTON

Junior Member

Hi Everyone.
I am finally getting around to fixing my Kustom 200 PA Head. Channels 2 and 4 are dead. I blew out the dust and applied deoxit to the pots. How do i check capacitors and or transistors. Sound appears to be OK from the other channels.
Thanks,
Brian

Report message to a moderator

Re: Help needed to troubleshoot Kustom PA 200 Channels [message #25648 is a reply to message #25647]

Tue, 18 October 2016 06:15

stevem
Messages: 4774
Registered: June 2004
Location: NY

Senior Member

Can you solder, do you have a tube type solder sucker,can you read a schematic and do you have a volt / ohm meter and know how to test transistors?

[Updated on: Tue, 18 October 2016 06:18]

Report message to a moderator

Re: Help needed to troubleshoot Kustom PA 200 Channels [message #25650 is a reply to message #25648]

Wed, 19 October 2016 06:00

stevem
Messages: 4774
Registered: June 2004
Location: NY

Senior Member

Even if you can just solder and unsoldering cleanly , changing out the first gain stage transistor will likely get both channels up and running , and the transistors these days are so cheap that it's fine to just shot gun the preamp boards and not even tests the transistors you yank out!

Report message to a moderator

Re: Help needed to troubleshoot Kustom PA 200 Channels [message #25651 is a reply to message #25647]

Wed, 19 October 2016 08:28

bproctor
Messages: 11
Registered: December 2015
Location: BOSTON

Junior Member

Thanks for the help.
I am OK at soldering, and have a multi-meter.
My neighbor is a whiz at electronics repair, and I will probably have him to the surgery.

I am just looking to do the leg work so that he has the information he needs (schematics, usual suspects, etc).

As far as the gain stage transistor is concerned, is there one of these per channel? This would be the first transistor after input.

Looks like the schematic links are down. I will try to print this out when it becomes available.

Thanks again

Report message to a moderator

Re: Help needed to troubleshoot Kustom PA 200 Channels [message #25653 is a reply to message #25647]

Wed, 19 October 2016 09:17

stevem
Messages: 4774
Registered: June 2004
Location: NY

Senior Member

The schematic section of this site is working fine, as I just tryed it.
You need to have your tech friend look at the PC105 schematic and change out transistor Q100 next to the boards volume pot .

Report message to a moderator

Re: Help needed to troubleshoot Kustom PA 200 Channels [message #25654 is a reply to message #25647]

Wed, 19 October 2016 12:10

chicagobill
Messages: 2006
Registered: April 2003

Senior Member

If your friend is a whiz, then he should first be able to test the transistors to see if that is the problem.

Report message to a moderator

Re: Help needed to troubleshoot Kustom PA 200 Channels [message #25656 is a reply to message #25647]

Wed, 19 October 2016 16:23

bproctor
Messages: 11
Registered: December 2015
Location: BOSTON

Junior Member

Great info. I will have him check it out and report back.
He mainly works on classic arcade video games, but this shouldn't be too much of a stretch
Thanks,
Brian

Report message to a moderator

Previous Topic:	Dead K 100 Piggyback
Next Topic:	K 200B-2 low volume

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Wed Nov 06 17:21:21 EST 2024