VintageKustom.com
VintageKustom.com is your source for literature and information on the tuck-and-roll vintage Kustom amps from the 60's and 70's, as well as their related products such as guitars and organs . We provide a webboard for help with kustom gear history, technical information and repairs as well as discussions with other collectors.

Home » VintageKustom.com » Repairing Kustom Amps » K100 with (2) 4-12" PA Cabinets (K100 PA Ohm load )
Show: Today's Messages :: Polls :: Message Navigator
Switch to threaded view of this topic Create a new topic Submit Reply
K100 with (2) 4-12" PA Cabinets [message #9715] Sat, 27 September 2008 01:16 Go to next message
hawk-bass is currently offline  hawk-bass
Messages: 2
Registered: January 2008
Location: Minneapolis, MN
Junior Member
I'm new here and it was nice to find this site, great job. I went through the postings and didn't find the answers I needed but did find a lot of good stuff.
I have a couple things to ask about if that's cool. I picked up a K100-B5, 4 channel PA head. There are no markings on the back of the amp (besides serial #plate) as to which are 1/4" output jack. I would assume it to be the 2 together up higher and in the center and the lower right had corner might be for a reverb foot switch? Also there is an RCA jack, is that standard?
Now for the cabinet question, as most of the wiring was totally gone inside when I got opened them, are they wired for 8ohm each for a 4 ohm load at the head?
Lastly, just wondering if you will be able to get the schematics back up? Retired road guy now playing for the fun of it, but I can still read a schematic.
Thanks
Hawkeye


Hawkeye
Re: K100 with (2) 4-12" PA Cabinets [message #9716 is a reply to message #9715] Sat, 27 September 2008 11:01 Go to previous messageGo to next message
LesS is currently offline  LesS
Messages: 478
Registered: December 2002
Senior Member
Hey Hawkeye,
Welcome to the site.
You are right - the two jacks that are together near the center are the speaker outputs.
The lower right jack is for a reverb footswitch.
The RCA jack is recording output.

The minumimum load for a K100 is 8 ohms.
So your speakers should be wired so that each cabinet is 16 ohms.
Both cabinets together would be a 8 ohm load.
Re: K100 with (2) 4-12" PA Cabinets [message #9718 is a reply to message #9715] Mon, 29 September 2008 07:08 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4773
Registered: June 2004
Location: NY
Senior Member
Welcome to the board!
So what color is your K100?
Re: K100 with (2) 4-12" PA Cabinets [message #9723 is a reply to message #9718] Thu, 02 October 2008 18:56 Go to previous message
hawk-bass is currently offline  hawk-bass
Messages: 2
Registered: January 2008
Location: Minneapolis, MN
Junior Member
Silver, found it at a pawn shop. Not a scratch on it. The speakers are a bit tough, but just for rehearsal room they're OK.
I found a stand for the head but need the clamp set for the cabinet, it just has the screws left in it, any ideas if those can even be found anywhere?
Thanks for the info too!I appreciate it.
Hawkeye


Hawkeye
  Switch to threaded view of this topic Create a new topic Submit Reply
Previous Topic: Noise problem??? HELP
Next Topic: Hum, hum, hum
Goto Forum:
  

-=] Back to Top [=-
[ Syndicate this forum (XML) ] [ RSS ]

Current Time: Sun Nov 03 12:40:40 EST 2024