VintageKustom.com: Replacement Part Suggestions

Home » VintageKustom.com » Replacement Part Suggestions » Patch/Speaker cable

Show: Today's Messages :: Polls :: Message Navigator

Patch/Speaker cable [message #22180]

Tue, 20 January 2015 15:02

slk854
Messages: 192
Registered: January 2015

Senior Member

I have just recently got a K150 and of course it did not come with a cable from the head to the speakers. I have been using an old guitar cable. What came with these originally? Was it one that was only about 3' long. Looks to me like a right angle to straight 3' would work perfect. Should they be of a certain guage??

Steve

Report message to a moderator

Re: Patch/Speaker cable [message #22182 is a reply to message #22180]

Tue, 20 January 2015 15:11

chicagobill
Messages: 2006
Registered: April 2003

Senior Member

You should never use a shielded guitar cable as a speaker cable, no matter what brand of amp you have.

The center conductor is much too small to carry the current that a speaker load will need. And the outside braid makes it that much easier for the cable to short, which may cause all sorts of damage to the power section of a solid state amp.

I would suggest a cable made from 18 gauge lamp cord, like a two wire extension cord. And it should be as short as reasonably possible.

Report message to a moderator

Re: Patch/Speaker cable [message #22183 is a reply to message #22180]

Tue, 20 January 2015 16:09

slk854
Messages: 192
Registered: January 2015

Senior Member

I would still have to use the 1/4" cable connectors and solder the 2 conductor round wire to them...Right. Thanks so much I was messing up big time. The exact reason I asked.

Steve

Report message to a moderator

Re: Patch/Speaker cable [message #22184 is a reply to message #22183]

Tue, 20 January 2015 16:21

Iowa Boy
Messages: 767
Registered: June 2014

Senior Member

I found buying chord already made up with jumbo jacks and 16 gauge works for me. Those small 1/4 jacks are hard to solder and the holes are always too small for the cable to fit in....not to mention a bigger jack is easier to get ahold of. Parts Express or MCM run sales all the time on cables.

Report message to a moderator

Re: Patch/Speaker cable [message #22185 is a reply to message #22180]

Tue, 20 January 2015 16:28

slk854
Messages: 192
Registered: January 2015

Senior Member

Do you have a link for them?

Steve

Report message to a moderator

Re: Patch/Speaker cable [message #22186 is a reply to message #22185]

Tue, 20 January 2015 16:32

Iowa Boy
Messages: 767
Registered: June 2014

Senior Member

Just google Parts Express or MCM Electronic's..................and search for speaker cables......

Report message to a moderator

Re: Patch/Speaker cable [message #22187 is a reply to message #22180]

Tue, 20 January 2015 16:36

Iowa Boy
Messages: 767
Registered: June 2014

Senior Member

Amazon is also a good place to look for deals on cables....always nice to have a couple of extra cables around....eventually one is going to short out anyway. I'm always stepping on one, or someone instead of pulling on the jack, pulls the cord instead. Now its a trip to the work bench.

Report message to a moderator

Re: Patch/Speaker cable [message #22201 is a reply to message #22180]

Wed, 21 January 2015 00:23

slk854
Messages: 192
Registered: January 2015

Senior Member

Did the originals have and angled connector that went into the speaker cab?

Report message to a moderator

Re: Patch/Speaker cable [message #22202 is a reply to message #22180]

Wed, 21 January 2015 03:05

riverboat
Messages: 49
Registered: November 2014
Location: United States

Member

I have made a bunch of these. Personally I like the smaller jacks as long as they are good enough quality so they don't fall apart. Also I like a straight jack at the amp end so I can grab hold of it easily but a angle jack at the speaker so I can park it next to a wall. This holds true for most head & cabinet set-ups, Not just Kustoms. Keith.

Report message to a moderator

Re: Patch/Speaker cable [message #22225 is a reply to message #22202]

Sat, 24 January 2015 00:39

Kustom_Bart
Messages: 601
Registered: October 2010
Location: Greenville, MichiGUN

Senior Member

For the cable, you know that old 2 prong power cord that you cut off and replace with a three prong power cord? It makes great speaker cable for just that type of thing. Use the straight plugs, I have never had good luck with the 90 degree ones holding up for very long.

Report message to a moderator

Previous Topic:	Power switch for Kustom 150
Next Topic:	Kustom Badge

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Fri Nov 01 19:21:24 EDT 2024