VintageKustom.com: Repairing Kustom Amps » Need some info for a k 200 b5 head.

Home » VintageKustom.com » Repairing Kustom Amps » Need some info for a k 200 b5 head.

Show: Today's Messages :: Polls :: Message Navigator

Need some info for a k 200 b5 head. [message #13521]

Sun, 02 May 2010 15:41

willc68
Messages: 15
Registered: May 2010
Location: philly

Junior Member

hello, i am new to the forum and maybe someone can help me out with some questions. I'd like to know what the correct impedance is for the 2 1/4 inch jacks on the back of the head? also what might the single 1/4inch jack that is right below the plate where the model and serial number is? would this be on/off for reverb? i am pretty sure this is a pa amp but i have been using it with guitar with excellent results just using a 12 inch speaker out of an old alamo amp. thanks, will

Report message to a moderator

Re: Need some info for a k 200 b5 head. [message #13522 is a reply to message #13521]

Sun, 02 May 2010 16:35

pleat
Messages: 1454
Registered: June 2004
Location: Belding, Mi

Senior Member

Welcome. Yes the K200-5 is the PA version. The total impedance would be 4 ohms for maximum 100 watt output. The 1/4" jack on the lower back right is for the reverb on/off footswitch. Kustom cabinets were 8 ohm each so with two columns the amp is running a 4 ohm load.
pleat

Report message to a moderator

Re: Need some info for a k 200 b5 head. [message #13524 is a reply to message #13521]

Mon, 03 May 2010 05:51

stevem
Messages: 4774
Registered: June 2004
Location: NY

Senior Member

Watch out if you care about that vintage Alamo speaker as even though its more than likly a 8 ohm driver that head will still output some 60 + watts into a 8 ohm load!

Report message to a moderator

Re: Need some info for a k 200 b5 head. [message #13541 is a reply to message #13522]

Mon, 03 May 2010 17:00

willc68
Messages: 15
Registered: May 2010
Location: philly

Junior Member

thanks a lot pleat for the valuable info, now i can start thinking about what i want to do for a permanent cabinet. thanks also stevem for your advice on the speaker. i really was not certain of the power rating so i was taking it easy on it. this is my first kustom amp and i am really blown away by it. i have a whole bunch of old tube amps but i needed something with a bit of power. my most powerful amp is a 59 silvertone 2-12 combo and i hate to travel with that so i lucked out on this pa head so now i want to get a nice sounding cab for messing about.

Report message to a moderator

Re: Need some info for a k 200 b5 head. [message #13544 is a reply to message #13521]

Tue, 04 May 2010 05:34

stevem
Messages: 4774
Registered: June 2004
Location: NY

Senior Member

My advice would be to get a 2-12 closed back cab loaded with 8 ohm drivers so that they can be wired in parallel for a 4 ohm which is what that head wants to see for maximum clean power.

Report message to a moderator

Previous Topic:	Kustom 1-L schematic
Next Topic:	Kasino Reverb Tank info.

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Mon Nov 04 23:46:02 EST 2024