VintageKustom.com: Repairing Kustom Amps

Home » VintageKustom.com » Repairing Kustom Amps » Schematic Accuracy (Missing components)

Show: Today's Messages :: Polls :: Message Navigator

Re: Schematic Accuracy [message #20179 is a reply to message #20097]

Tue, 18 February 2014 13:58

chicagobill
Messages: 2006
Registered: April 2003

Senior Member

Good catch on the ballast resistor. "Gee, I've got a resistor that's the right size to fit in there!" Unless it was meant to be R215 in the pilot lamp circuit.

Changing the tantalums for an normal electrolytic should not make any difference, at least not in these amps. As long as the correct values and voltage ratings are observed.

Interference is possible at any voltage level, frequency is probably more of a factor though.

You can try increasing the values of C133 and C134 on the output of the two 8 volt supplies. You can also try bypassing C133 and C134 with a 0.1uf cap.

Report message to a moderator

[Message index]

		Schematic Accuracy By: bluezebra on Mon, 10 February 2014 01:29
		Re: Schematic Accuracy By: stevem on Mon, 10 February 2014 06:30
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 10:19
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 10:26
		Re: Schematic Accuracy By: chicagobill on Mon, 10 February 2014 12:40
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 13:00
		Re: Schematic Accuracy By: stevem on Mon, 10 February 2014 13:17
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 13:41
		Re: Schematic Accuracy By: chicagobill on Mon, 10 February 2014 16:24
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 17:10
		Re: Schematic Accuracy By: bluezebra on Mon, 10 February 2014 17:33
		Re: Schematic Accuracy By: chicagobill on Tue, 11 February 2014 12:22
		Re: Schematic Accuracy By: bluezebra on Tue, 11 February 2014 13:25
		Re: Schematic Accuracy By: stevem on Wed, 12 February 2014 09:26
		Re: Schematic Accuracy By: bluezebra on Wed, 12 February 2014 12:55
		Re: Schematic Accuracy By: stevem on Wed, 12 February 2014 17:08
		Re: Schematic Accuracy By: bluezebra on Wed, 12 February 2014 17:20
		Re: Schematic Accuracy By: bluezebra on Wed, 12 February 2014 21:22
		Re: Schematic Accuracy By: chicagobill on Thu, 13 February 2014 10:43
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 13:57
		Re: Schematic Accuracy By: chicagobill on Thu, 13 February 2014 14:40
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 15:20
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 15:25
		Re: Schematic Accuracy By: chicagobill on Thu, 13 February 2014 16:14
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 17:39
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 19:36
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 22:03
		Re: Schematic Accuracy By: bluezebra on Thu, 13 February 2014 22:40
		Re: Schematic Accuracy By: chicagobill on Fri, 14 February 2014 13:04
		Re: Schematic Accuracy By: bluezebra on Fri, 14 February 2014 22:38
		Re: Schematic Accuracy By: stevem on Sat, 15 February 2014 07:43
		Re: Schematic Accuracy By: bluezebra on Sat, 15 February 2014 10:28
		Re: Schematic Accuracy By: bluezebra on Sat, 15 February 2014 12:11
		Re: Schematic Accuracy By: stevem on Mon, 17 February 2014 06:33
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 11:07
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 11:33
		Re: Schematic Accuracy By: chicagobill on Mon, 17 February 2014 13:25
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 14:20
		Re: Schematic Accuracy By: chicagobill on Mon, 17 February 2014 14:54
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 16:56
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 17:14
		Re: Schematic Accuracy By: bluezebra on Mon, 17 February 2014 17:36
		Re: Schematic Accuracy By: chicagobill on Tue, 18 February 2014 12:24
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 13:31
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 13:37
		Re: Schematic Accuracy By: chicagobill on Tue, 18 February 2014 13:58
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 18:25
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 20:53
		Re: Schematic Accuracy By: chicagobill on Tue, 18 February 2014 21:38
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 23:15
		Re: Schematic Accuracy By: bluezebra on Tue, 18 February 2014 23:17
		Re: Schematic Accuracy By: chicagobill on Wed, 19 February 2014 01:44
		Re: Schematic Accuracy By: bluezebra on Wed, 19 February 2014 10:32
		Re: Schematic Accuracy By: chicagobill on Wed, 19 February 2014 11:13
		Re: Schematic Accuracy By: bluezebra on Wed, 19 February 2014 12:21
		Re: Schematic Accuracy By: chicagobill on Wed, 19 February 2014 13:20
		Re: Schematic Accuracy By: bluezebra on Wed, 19 February 2014 14:02
		Re: Schematic Accuracy By: bluezebra on Wed, 19 February 2014 14:05
		Re: Schematic Accuracy By: chicagobill on Wed, 19 February 2014 17:06
		Re: Schematic Accuracy By: bluezebra on Wed, 19 February 2014 23:21
		Re: Schematic Accuracy By: stevem on Thu, 20 February 2014 06:49
		Re: Schematic Accuracy By: bluezebra on Thu, 20 February 2014 12:03

Previous Topic:	Kustom Studio 2 Valve head with fried board
Next Topic:	footswitch K200A PA

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Sun Nov 03 02:35:09 EST 2024