VintageKustom.com
VintageKustom.com is your source for literature and information on the tuck-and-roll vintage Kustom amps from the 60's and 70's, as well as their related products such as guitars and organs . We provide a webboard for help with kustom gear history, technical information and repairs as well as discussions with other collectors.

Home » VintageKustom.com » Repairing Kustom Amps » Kustom 150-2
Show: Today's Messages :: Polls :: Message Navigator
Switch to threaded view of this topic Create a new topic Submit Reply
Kustom 150-2 [message #6861] Wed, 05 April 2006 18:06 Go to next message
doctrjazz is currently offline  doctrjazz
Messages: 6
Registered: April 2006
Location: Va
Junior Member
I just bought a Kustom 150-2 and know very little about this set up.. My problem is when I play through it and I set the volume up to about 5 the low B string on my bass rattles the speakers really bad... As the band plays in Drop D a lot, is there a solution like setting up the tone controls or something or is this just the nature of the 2-12's which have been replace in the last year with minimal play time on them...I have always used a 15 or 18...I have been trying to "dial" it in but no luck as of yet and I want to use it on the gig tomorrow... Any advice??? Thanks
Re: Kustom 150-2 [message #6863 is a reply to message #6861] Wed, 05 April 2006 21:21 Go to previous messageGo to next message
LesS is currently offline  LesS
Messages: 478
Registered: December 2002
Senior Member
At five you are at or close to the maximum clean output of the amp. Generally on the Kustoms, you hit full volume around 4. It is 75 watts RMS which might not be enough for you depending on your speakers. What speakers and what cabinet do you have? What ohms are the speakers?
A lot of cabinets have trouble with bass notes that low. Also try running the bass control at 12 o'clock or lower.
-Les S
Re: Kustom 150-2 [message #6865 is a reply to message #6861] Thu, 06 April 2006 07:50 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4773
Registered: June 2004
Location: NY
Senior Member
Hi, 2-12 inch speakers are real not the way to go for a 5 string bass, even 12 pro model woffers have a hard time moving that much air and most of them need above 300 watts in a big cabinet to do it. That low B string is at 30 cycles or so, and most 12 inch speakers start to lose SPL level real fast by around 70 to 50 cycles if they are guitar speakers. You need at least a 15 incher that will go down to 40 cycles in a good ported cabinet. And if you are playing out with a hard hitting drummer 2 15s would be better. I have not tested my K150 as I have my others yet, to truly find out if they put out more wattage at 8 ohms or 4 ohms. I will set mine up over the week end and put up a post on it monday to let you all know.For playing you can rent a power amp and a cab since the head has a jack to drive a power amp.
Re: Kustom 150-2 [message #6866 is a reply to message #6861] Thu, 06 April 2006 09:38 Go to previous messageGo to next message
KustomKyle is currently offline  KustomKyle
Messages: 14
Registered: February 2006
Junior Member
This might be the strangest answer you guys have ever heard - but do you have all of the screws on the back panel screwed into the cabinet? When I bought my Kustom, it only had about 7 of the 30 (give or take a few) screws/washers screwed into the holes in the cabinet. And whenever I played it at higher volume, the amp would rattle like crazy. At first I thought it was the speakers, but then I had someone play through it while I really inspected it - and it turned out that it was the back panel rattling the whole time. I replaced the screws/washers in all of the holes, and the problem was immediately solved. That being said - I have a 2X15 cabinet that I play bass through - so your problem might be completely different since you're running through 2 12's.
Re: Kustom 150-2 [message #6867 is a reply to message #6861] Thu, 06 April 2006 10:43 Go to previous messageGo to next message
doctrjazz is currently offline  doctrjazz
Messages: 6
Registered: April 2006
Location: Va
Junior Member
Thanks in advance to all who have offered advice... I have not inspected the screws in the back but I did have a "home made cab" before I bought this one and the screws in the speaker were loose and I have the same prob... I will be using the kustom with the 2-12 and a Peavy TK-80 "15" tonight and tomorrow... That way I can dial in the kustom for for the good clarity of mids and high and dial in the Peavy for the bottom... I personally feel the 12's just are not able to handle the lower notes due the frequency... If any one wants to check out the band we are at
http://www.tagworld.com/doctrjazz -- my personal page
http://www.tagworld.com/factoryair
http://unsignedbandweb.com/music/bands/5288/ http://www.myspace.com/factoryairband http://www.garageband.com/artist/FactoryAir http://www.mybandscene.com/factoryairbooking http://www.localbandnetwork.com/Bands/banddetail.cfm?BandID= 24792
Come check us out if you like tagworld is probably our best page... And thanks to all who helped and will post again after the gigs and let you know how the set up worked.. Also where can I get a schematic and lay out for the slat face '71 head??? Thanks Again Billy

[Updated on: Thu, 06 April 2006 10:44]

Report message to a moderator

Re: Kustom 150-2 [message #6868 is a reply to message #6861] Thu, 06 April 2006 12:34 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4773
Registered: June 2004
Location: NY
Senior Member
I have one, I can fax it or slap one in a envelope to you.
Re: Kustom 150-2 [message #6869 is a reply to message #6868] Thu, 06 April 2006 14:48 Go to previous messageGo to next message
doctrjazz is currently offline  doctrjazz
Messages: 6
Registered: April 2006
Location: Va
Junior Member
Either way I really appreciate it email to doctrjazz@verizon.net or fax to ATTN: CM2 WILLIAM WADE (540) 366-9031 and again I really appreciate it... Thanks Billy
Re: Kustom 150-2 [message #6883 is a reply to message #6861] Mon, 10 April 2006 07:54 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4773
Registered: June 2004
Location: NY
Senior Member
I am getting my schematic back in hand tonight, and I will fax you it on tuesday.Sorry for the delay!
Re: Kustom 150-2 [message #6887 is a reply to message #6883] Mon, 10 April 2006 12:27 Go to previous messageGo to next message
doctrjazz is currently offline  doctrjazz
Messages: 6
Registered: April 2006
Location: Va
Junior Member
Thanks Again and I will be looking for it...
Re: Kustom 150-2 [message #6888 is a reply to message #6887] Mon, 10 April 2006 12:31 Go to previous messageGo to next message
doctrjazz is currently offline  doctrjazz
Messages: 6
Registered: April 2006
Location: Va
Junior Member
I took the Kustom and a Peavy TKO 80 to the gigs... I ran the tape out on the Kustom to the Peavy and rolled back the lows and some of the mids on the Kuston. Gave it a reall brite and punchy sound and then dialed in the lower freqs on the Peavey... Made for a heck of a rig... I was able to compete with a Marshall and a Butcher with 4 12 cabs... My complements on the Kustom, really ended up liking it... My next question is what is the average cost of this amp set up... 150-2 slant face (1971) with matching cab 2-12 tuck and roll is in excellent shape and head is very clean...
Re: Kustom 150-2 [message #6889 is a reply to message #6861] Mon, 10 April 2006 12:49 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4773
Registered: June 2004
Location: NY
Senior Member
It depends, 400 to 500 if someone has a bad enough itch for it.If you 2 12 cab is the one with jensen speakers, the C12N model, those are worth 150 to 200 each alone!
Re: Kustom 150-2 [message #6900 is a reply to message #6889] Wed, 12 April 2006 16:19 Go to previous message
doctrjazz is currently offline  doctrjazz
Messages: 6
Registered: April 2006
Location: Va
Junior Member
I go the fax today... Thank you very much... And thanks again to all who provided help...Billy
  Switch to threaded view of this topic Create a new topic Submit Reply
Previous Topic: Short circuitinga 4-pin-male-out when no Footcontrols available
Next Topic: New guy-asking for your help!
Goto Forum:
  

-=] Back to Top [=-
[ Syndicate this forum (XML) ] [ RSS ]

Current Time: Sat Nov 02 06:04:57 EDT 2024