| KUSTOM - Hustler and Commander [message #25232] |
Sun, 17 July 2016 03:07  |
LeeNails
Messages: 26
Registered: June 2016
Location: earth
|
Junior Member |
|
|
I've been needing a good combo for my Clean sound for gigs. I found an As-Is 70's Commander 1-15 on the Music-Go-Round website and am having it shipped in from WI. The store sold it cheap As-Is because it's noisy as all git out when an instrument isn't plugged into it, and the reverb is apparently dead.
After paying for the Commander, I happened upon a 70's Hustler 4x10 in the local Craigslist, which was described as fully functional. Upon inspection, I discovered that it was all good to go. . . .except for the crappy, distorted sounding reverb.
Now I've got one iffy Kustom in hand, and another on the way! LOL.
It looks to me like the Commander and the Hustler are exactly the same amp, only with different speaker systems. I'd likely rather gig with the smaller of the two. . . perhaps the Commander.
Anyway, just wondered if any of you experts had info, tips, advice or horror stories to share about these Metal-Face wonders and their reverbs.
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25234 is a reply to message #25232] |
Sun, 17 July 2016 06:50  |
stevem
Messages: 4775
Registered: June 2004
Location: NY
|
Senior Member |
|
|
The first thing to do with either amp is to unplug and plug back in a few times all of the white Molex connectors that these amps have from board to board.
On the Female pins in these connector you can tighten them up with a needle nose .
On the reverb issue do the same thing to its RCA cable at each end, but also spin them as you take them on and off as the Female's ends on both the pan side and board tarnish up really bad at times.
Be very carefull when plugging the Molex connectors back into place as you should try to support the under side of the board where the connectors are solder into.
See if these 10 minute worth of things helps out!
[Updated on: Sun, 17 July 2016 06:53] Report message to a moderator |
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25236 is a reply to message #25232] |
Mon, 18 July 2016 00:35 |
chicagobill
Messages: 2006
Registered: April 2003
|
Senior Member |
|
|
A few years ago I bought two dead Kustom chassis, one was a Hustler. I rebuilt it and it's one of my favorite sounding Kustom amps. Loud enough to gig with, great reverb and vibrato.
One problem with mine was broken solder connections on the Molex jacks on the boards. The important one is the ground connection from the power amp to the FX board. If that ground connection breaks, the power amp might blow an output transistor.
So as Steve suggested, clean those connectors and check the solder connections on the pc boards.
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25238 is a reply to message #25236] |
Thu, 21 July 2016 05:44 |
LeeNails
Messages: 26
Registered: June 2016
Location: earth
|
Junior Member |
|
|
The Sidewinder showed up today, and the problem with the reverb was immediately obvious. . . . NO PAN!
So, which pan ought I to get for it, maker, model #????
I work in a store, so I might be able to get one from one of our suppliers . . but just in case, where do You all typically get such things?
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25266 is a reply to message #25232] |
Fri, 22 July 2016 17:50 |
chicagobill
Messages: 2006
Registered: April 2003
|
Senior Member |
|
|
I dug through my notes and I have the metal front tank for the 150-250 amps as being a 4BB2C1D. So as best as I can tell, you need need a 4BB2C1B for your amps.
The only difference is the last letter that represents how the tank is meant to be mounted. D is for vertical mounting and the B is for horizontal.
Before anything else, you should check the tank that you have and see if it is the original tank or if it has been replaced. If it has been replaced, it may not be the right one and it may be the cause of your bad reverb sound.
Look at the tank and see if there is a code number rubber stamped on the case. If not we can tell you if the tank is original or not by the physical and electrical characteristics. Do you have an ohm meter?
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25270 is a reply to message #25266] |
Sat, 23 July 2016 00:24 |
LeeNails
Messages: 26
Registered: June 2016
Location: earth
|
Junior Member |
|
|
I took the tank out of the Hustler and the number rubber stamped on it is: 031-0047-00
There is also the mumber: 1122 stamped into the metal of the tank, which is an Accutronics tank.
I removed the Hustler's tank and transplanted it into the Sidewinder, and it sounded just as crappy in THAT. It sounds like there's a distant, crappy distortion box along with the reverb or something. Yuck!
When I was testing the Hustler earlier, and was cranking the volume up and down, I noticed some evil sounding noises intermittently erupting from the amp. Sounded like some old components were complaining or something. Other than that, it sounded pretty cool. In contrast, I didn't find the sound of the Sidewinder as pleasing, and it didn't seem to have as much high end sparkle as the Hustler. . . .maybe because of its' single 15 speaker.
I'm seriously considering having both amps re-capped or something by a pro. . . .unless there's a good YouTube video showing how to do it.
I live in the East Bay here in California. . .anybody know any good local techs who like Kustoms???
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25271 is a reply to message #25270] |
Sat, 23 July 2016 00:26 |
LeeNails
Messages: 26
Registered: June 2016
Location: earth
|
Junior Member |
|
|
|
. . . .oh and yeah, I DID unplug and re-plug the reverb RCA connections at the amp and at the tank several times, and also carefully unplugged and re-plugged the Molex connectors too.
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25276 is a reply to message #25266] |
Sat, 23 July 2016 23:33 |
LeeNails
Messages: 26
Registered: June 2016
Location: earth
|
Junior Member |
|
|
In the CE Distribution 2016 catalog (page 77) under Accutronics Reverb Tanks there is listed under the sub-heading 'Type 4 (Long, 2 Spring)
P-RK-4BB2C1B, which has specs listed as: Input=150 ohms Output=2,250 ohms Decay=medium Used in=Crate(? . . LOL)
Is THIS the tank I need for the Hustler and Sidewinder?
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25277 is a reply to message #25232] |
Sun, 24 July 2016 01:23 |
chicagobill
Messages: 2006
Registered: April 2003
|
Senior Member |
|
|
Yes, that tank should work fine.
I looked up the number that you posted and 031-0047-01 is the Kustom part number for the tank used in the 150-250 metal fronts. I haven't pulled out the schematics for the hustler or sidewinder yet, but it probably is the same part number.
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25278 is a reply to message #25277] |
Sun, 24 July 2016 01:54 |
LeeNails
Messages: 26
Registered: June 2016
Location: earth
|
Junior Member |
|
|
When I pulled the tank from the Hustler it didn't look like it had ever been removed. . very much like it was the original part. However, it is mystifying that BOTH the Hustler AND the Sidewinder exhibited the Same sort of funky distortion sound with that tank installed. Although my testing would tend to point to the Wrong reverb unit being the culprit . . how Could it be if it's the original part??? Unless the tank is defective or damaged in such a way as to render it capable of causing those crappy sounds. The tank is a pretty simple unit from what I can see. . . so, it seems kinda unlikely to me that it could be damaged to that degree and not Look damaged at all. The unit looks totally sound and whole. Could there possibly be something up with it that would miss visual inspection???
Also, is the Accutronic part I described from the catalog the proper unit? If I bought the new tank and plugged it in, and either or Both amps worked as normal, then I guess that would mean the original tank was to blame.
If Both amps really do have (as they now appear to) identical component failures in the reverb circuit. . .I'd assume this is a common problem with this series. Is it?
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25279 is a reply to message #25277] |
Sun, 24 July 2016 01:58 |
LeeNails
Messages: 26
Registered: June 2016
Location: earth
|
Junior Member |
|
|
|
by the way. . . .I should belatedly clarify the initial mistake in my original posting . . it should have read KUSTOM - Hustler and Sidewinder, as it's the Sidewinder I just bought. . . I once owned a Commander back in the 90's. . .I got confused, sorry. Also, how different (if at All) are the circuits of the Hustler and Sidewinder? Mine sound quite different, the Hustler sounding much more crisp and sparkly.
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25280 is a reply to message #25232] |
Sun, 24 July 2016 13:56 |
chicagobill
Messages: 2006
Registered: April 2003
|
Senior Member |
|
|
I haven't had a chance to look up the Hustler/Sidewinder schematic to see if there is a Kustom part number listed yet, so I could only assume that the tank that you have is correct.
My Huster's reverb sounds very typical of any Kustom reverb, no distortion, etc. I love the tone control that lets you get a bright or dark reverb.
There could be something wrong with your tank or there could be something wrong with both of your amps, I don't know. If you order a new tank and try it with both amps, you will have your answer. But logic would tend to support the theory that there is something wrong with the tank and not both amps.
The metal front circuit drives the reverb tank with an op amp ic. The tank's input transducer is part of the op amp's feedback loop, so neither end of the coil should be grounded. Therefore the tank's input jack should be isolated from the chassis. Check the tank and see if the RCA jack that is marked INPUT is the insulated type.
Have you checked to see that the tank is plugged in correctly?
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25281 is a reply to message #25280] |
Sun, 24 July 2016 17:20 |
LeeNails
Messages: 26
Registered: June 2016
Location: earth
|
Junior Member |
|
|
|
The Hustler's reverb tank seems to be original equipment, but I have no idea if it was plugged in correctly. The input and output are clearly marked on the tank, but the RCA input jacks on the back of the chassis are NOT marked. I carefully marked the top plug and installed the cords exactly as they were on the Hustler when I tried it in the Sidewinder. I will reverse those cords and see if it results in any change in function.
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #25282 is a reply to message #25281] |
Sun, 24 July 2016 17:31 |
LeeNails
Messages: 26
Registered: June 2016
Location: earth
|
Junior Member |
|
|
The reversal of the RCA plugs into the inputs on the chassis of the Sidewinder was successful. The weird distortion sound has vanished!!! YEA! I guess I should assume that the problem with the Hustler was the same thing, so I'll most likely put this tank back in the Hustler, plugged in correctly and use the Hustler with the band . . since I prefer its' tone to the Sidewinder.
Now I just need to get the proper replacement tank for the Sidewinder and make sure it is properly installed.
|
|
|
|
|
|
|
|
| Re: KUSTOM - Hustler and Commander [message #27620 is a reply to message #25232] |
Sat, 14 December 2019 06:11 |
stevem
Messages: 4775
Registered: June 2004
Location: NY
|
Senior Member |
|
|
Thanks for the info on that fix!
Yes, Tantalums where the new rag way back then due to there small size and what I do as a matter of course when working on any Amp is just replace them all since I am in there anyway!
|
|
|
|
VintageKustom.com
Search
Help
Members
Register
Login
Home
]