VintageKustom.com: Replacement Part Suggestions

Home » VintageKustom.com » Replacement Part Suggestions » Replcement Ball Casters

Show: Today's Messages :: Polls :: Message Navigator

Replcement Ball Casters [message #29063]

Wed, 26 July 2023 15:47

rodak
Messages: 516
Registered: October 2001
Location: Georgia

Senior Member

One of the casters on my K200 is missing some bearings, and the cabinet tends to swerve pretty bad to one side - really annoying. Perusing old posts here it seems Grainger was the go-to supplier for good ball casters, but at one point I saw it mentioned that they were no longer made, or priced too high. Well, taking the supplied part number (5X758) to grainger.com showed they were indeed discontinued, but they had a link to a replacement:

https://www.grainger.com/product/GRAINGER-APPROVED-Standard- Plate-Caster-2-in-437V29?opr=ILOF

Looks pretty good, and the price is certainly right, almost too good - a buck.43 each? Even with shipping, a set of four will set me back less than 20 bucks.

Anyone see anything wrong with these? The size and weight capacity appear to be the same.

www.combo-organ.com

Report message to a moderator

Re: Replcement Ball Casters [message #29064 is a reply to message #29063]

Thu, 27 July 2023 18:19

stevem
Messages: 4775
Registered: June 2004
Location: NY

Senior Member

At one time Peavey had them as replacements also and I picked up 3 set of four and I think the price was 24 bucks.

Heck, at the price you found those for then why not pick up 2 sets so as to have a few spares in case they are lacking quality.

Report message to a moderator

Re: Replacement Ball Casters [message #29065 is a reply to message #29063]

Thu, 27 July 2023 19:50

rodak
Messages: 516
Registered: October 2001
Location: Georgia

Senior Member

Good idea! I ordered 8, for when I eventually find a 2x15 or 3x15 cabinet. $26 bucks shipped - wottadeal!

www.combo-organ.com

Report message to a moderator

Re: Replcement Ball Casters [message #29070 is a reply to message #29063]

Sat, 29 July 2023 20:21

rodak
Messages: 516
Registered: October 2001
Location: Georgia

Senior Member

Casters came in today, and they're exact replacements! Look exactly like the originals and fit perfectly - no re-drilling necessary.

The only tricky bit is getting some of the old screws off. I removed the bottom plates(which was no problem), and was able to get one caster off, but on the 2nd one, it started stripping one of the screws, as the nut was so frozen onto it. Second screw did the same thing so I stopped. Any suggestions other than soaking it in Liquid Wrench (which I'm doing tonight)?

www.combo-organ.com

Report message to a moderator

Re: Replcement Ball Casters [message #29071 is a reply to message #29063]

Sun, 30 July 2023 09:07

stevem
Messages: 4775
Registered: June 2004
Location: NY

Senior Member

I use a spray called PB blaster, it puts LW to shame!

What I do before trying to break any screw free that's been tightened down for decades and especially if it shows traces of rust is to first beat on it with a big near sharp nose punch while it's supported well so all of the impact goes into the screw.

This will action will stretch the threads out some and loosen it up.

As far as getting the screw out at that point if the head is too chewed up for a screw driver then just like with auto repair work get a left handed drill bit to drill it out with.

When worse comes to worse I have made a new main bar out of 1/8" thick Aluminum bar stock.
It's sold in 3 ft lengths.

Report message to a moderator

Re: Replcement Ball Casters [message #29073 is a reply to message #29071]

Mon, 31 July 2023 09:35

rodak
Messages: 516
Registered: October 2001
Location: Georgia

Senior Member

Thanks. I'll look for PB Blaster.
Soaking in Liquid Wrench didn't help. I was able to replace the other three casters, and now the cab will roll nicely without constantly wanting to turn in one direction, which was what started me down this path.

If I wind up having to drill out the stuck screws, do you know of a source for replacements? I could check Ace Hardware, but those screws don't look like something I'd be likely to find there, they seem just a bit unusual.

www.combo-organ.com

Report message to a moderator

Re: Replcement Ball Casters [message #29356 is a reply to message #29063]

Fri, 25 October 2024 09:51

KustomBlues
Messages: 494
Registered: June 2001
Location: Michigan

Senior Member

I have one extra original caster. Let me know if you still need it.

Deb

Report message to a moderator

Previous Topic:	Replacement Pilot Bulb for Kustom 200
Next Topic:	Standel S115 speakers in a 215 Kustom cab...?

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Mon Nov 18 11:05:40 EST 2024