VintageKustom.com: Repairing Kustom Amps » K250-1 bulbs in switches

Home » VintageKustom.com » Repairing Kustom Amps » K250-1 bulbs in switches (What is the correct voltage for the bulbs)

Show: Today's Messages :: Polls :: Message Navigator

K250-1 bulbs in switches [message #29231]

Thu, 18 April 2024 09:43

Jerry H
Messages: 3
Registered: April 2024

Junior Member

I am working on a K250-1 for a friend's grandson. I have wired a 3 wire cord. I have swapped the working and intact polarity switch for the broken power switch. I have removed the wiring to the polarity switch except for the green wire for the bulb terminal located at the end of the switch which remains. The other terminal goes to ground. The amp is working fine. I have 335 replacement bulbs which I understand are 28 volts. However, I measure 40 volts at the bulb terminal. Is this normal? If so, what keeps the bulbs from burning out? Thanks in advance. Jerry H

Report message to a moderator

Re: K250-1 bulbs in switches [message #29232 is a reply to message #29231]

Thu, 18 April 2024 12:16

stevem
Messages: 4774
Registered: June 2004
Location: NY

Senior Member

I can only guess that your measurements are with no bulb in that circuit and if that's the case then that's why your measuring the full 40 volts that the power supply has.

With no bulb in the circuit there is no current draw thru the resistors bolted down on the floor of the chassis that drop the 40 volts down to 28.

The short of it is no bulb, no current draw and there for no voltage drop.

Report message to a moderator

Re: K250-1 bulbs in switches [message #29233 is a reply to message #29231]

Thu, 18 April 2024 12:20

stevem
Messages: 4774
Registered: June 2004
Location: NY

Senior Member

Note that if you only have 1 bulb in the amp then with the lesser load the voltage on the bulb your powering will be higher then 28 volts, so that will to some extent shorten the life of that bulb.

Report message to a moderator

Re: K250-1 bulbs in switches [message #29234 is a reply to message #29231]

Thu, 18 April 2024 15:25

Jerry H
Messages: 3
Registered: April 2024

Junior Member

SteveM, you are amazing. I feel a bit like a doofus. In any event, I appreciate you and the group. Jerry H

Report message to a moderator

Re: K250-1 bulbs in switches [message #29235 is a reply to message #29231]

Thu, 18 April 2024 18:50

stevem
Messages: 4774
Registered: June 2004
Location: NY

Senior Member

Don't kick yourself !

Back in the 70s when myself and 24 other kids where in tech school for electronics and after all the needed math the teacher had us troubleshooting a circuit that had no problem .
He knew it had no problem but of course did not tell us, and the voltage we all where reading was high due to no load.
Do you think any of us newbies even after the math / ohms law lesson figured out that there simply was no problem, nope none of us ! Lol.

Report message to a moderator

Re: K250-1 bulbs in switches [message #29236 is a reply to message #29231]

Fri, 19 April 2024 06:55

Jerry H
Messages: 3
Registered: April 2024

Junior Member

Just a quick follow up. I measured the resistance of the 335 bulbs and found it to be +/-65 ohms. Thanks again.

Report message to a moderator

Previous Topic:	Information on Voicing Control
Next Topic:	Active Bass and K250 preamp damage

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

]

Current Time: Tue Nov 05 06:19:28 EST 2024