VintageKustom.com
VintageKustom.com is your source for literature and information on the tuck-and-roll vintage Kustom amps from the 60's and 70's, as well as their related products such as guitars and organs . We provide a webboard for help with kustom gear history, technical information and repairs as well as discussions with other collectors.
Home » VintageKustom.com » Replacement Part Suggestions » Cabinet Handles & Ball Caster plates
Show: Today's Messages :: Polls :: Message Navigator
Switch to threaded view of this topic Create a new topic Submit Reply
Cabinet Handles & Ball Caster plates [message #24750] Mon, 14 March 2016 11:37 Go to next message
GaryLC is currently offline  GaryLC
Messages: 58
Registered: December 2012
Member
I've got a 200 bass cabinet with very rusty handle hardware, and rusty & bent plates on the bottom that the casters mount to. Any recommendations as to where I can find exact replacements, I want her to shine!!

Report message to a moderator

Re: Cabinet Handles & Ball Caster plates [message #24751 is a reply to message #24750] Mon, 14 March 2016 13:53 Go to previous messageGo to next message
carlc is currently offline  carlc
Messages: 143
Registered: July 2006
Location: Summerville, SC
Senior Member
You should be able to straighten the plates and clean them up with wire brush/sandpaper. Original handles can't be found. Brettun's Village has a replacement here: http://www.brettunsvillage.com/trunks/howto/parts/schandles. htm about half way down the page. You have to use the plastic insert or use your old mount.

Report message to a moderator

Re: Cabinet Handles & Ball Caster plates [message #24753 is a reply to message #24750] Mon, 14 March 2016 14:50 Go to previous messageGo to next message
stevem is currently offline  stevem
Messages: 4775
Registered: June 2004
Location: NY
Senior Member
The bottom caster mount sub plates can be replaced with 1/8" thick flat aluminum bar stock that can be had at most hardware stores .

Report message to a moderator

Re: Cabinet Handles & Ball Caster plates [message #24755 is a reply to message #24750] Mon, 14 March 2016 20:18 Go to previous messageGo to next message
GaryLC is currently offline  GaryLC
Messages: 58
Registered: December 2012
Member
Thanks, guys!!

Report message to a moderator

Re: Cabinet Handles & Ball Caster plates [message #25249 is a reply to message #24755] Thu, 21 July 2016 16:01 Go to previous message
LeeNails
Messages: 26
Registered: June 2016
Location: earth
Junior Member


these look pretty good:


http://www.ebay.com/itm/191889729204?_trksid=p2055119.m1438. l2649&ssPageName=STRK%3AMEBIDX%3AIT

. . .not the 'plates' but the casters:

http://www.ebay.com/itm/201585907025?_trksid=p2055119.m1438. l2649&ssPageName=STRK%3AMEBIDX%3AIT

[Updated on: Thu, 21 July 2016 16:01]

Report message to a moderator

  Switch to threaded view of this topic Create a new topic Submit Reply
Previous Topic: Kasino Cabinet Casters
Next Topic: KUSTOM - Sidewinder
Goto Forum:
  

-=] Back to Top [=-
[ Syndicate this forum (XML) ] [ RSS ]

Current Time: Sat Nov 16 00:32:02 EST 2024
.:: Contact :: Home ::.

Powered by: FUDforum 3.1.3.
Copyright ©2001-2023 FUDforum Bulletin Board Software